mooxsonar432.weebly.com Open in urlscan Pro
74.115.51.8  Public Scan

Form analysis
0 forms found in the DOM

Text Content

 * Blog


mooxsonar





DOES BASS PRO SHOPS INSTALL FISH FINDERS

11/24/2018

0 Comments

 
 * Bass Pro Shops Depth Finders
 * Fish Finders Bass Pro Shops

Step-by-step instructions on how to install a fishfinder on your helm. Fish
Finders. You can wait. This is a straightforward job and shouldn't take a pro
more. Buy the Garmin Striker 4 Sonar Fishfinder and GPS Plotter and more quality
Fishing, Hunting and Outdoor gear at Bass Pro Shops. So if you can't install a
fish finder to your boat permanently. Bass Pro Shops. Most fishermen really like
their Lowrance HDS Gen 3 fish finders.

Installing your fish finder the correct way will ensure that you get the most
out of it. Taking a little extra time and effort to do it properly the first
time will lead up to a lot of enjoyable fishing outings ahead! Step 1: Figure
out where to mount the transducer This is by far the most important and most
sensitive step of the installation. Most units ship with a transom mount
transducer, which you can easy install at home with tools you can find in your
garage or shed.


BASS PRO SHOPS DEPTH FINDERS

If you opted for a thru-hull transducer, it is best to have it done
professionally as the installation is a lot more complicated and involves
cutting a hole in the bottom of your boat! Some people advocate finding a place
for your fish finder first, saying that you need to know where to run the wires
to. It is more practical to first install the transducer then see how far the
wires run – you can move your fish finder unit around, but your transducer has
to go on the transom!

Look on the hull for a spot that always stays submerged in the water. Your
transducer has to be in contact(preferably submerged) with the water at all
times, otherwise it won’t function! You should also take into account how smooth
that part of the transom is, how far away from the propeller it is(preferably
12-14″), and if there is anything nearby that might disturb the flow of water.

The more turbulence there is, the more disturbance there will be in the reading.
You should also consider where the position of the transducer will be when your
boat is trailered – make sure it’s situated in a way that it doesn’t get bumped
around.

Make sure that the transducer sits perfectly horizontal. Step 2: Test-run the
wires Before we actually screw the transducer in, it’s good to test-run the
wires from it to the main unit and from the main unit to the battery. If we did
it after screwing it in, an accidental tug on the wire might cause the sealant
we will apply to seal the holes to loosen. If your wires are a little long, DO
NOT cut them!

Cutting wires in any way will VOID your manufacturer’s warranty! Instead, coil
and clamp the wires or fasten them with ties near the main unit, NOT near the
transducer. WARNING: Do not run the transducer wire with the engine’s wiring
harness or the VHF cable as this can cause interference that will mess up the
fish finder’s performance. Step 3: Mount the transducer Once you have found a
good spot, stick a plastic block on it – you will mount the transducer on this
block, so you don’t have to drill any unnecessary holes in your boat. Allow
enough time for the block’s epoxy or glue to dry and stick strongly. Place the
transducer on the block in a position as discussed above, and mark the holes
with a pencil.

This is where you will be drilling. If you choose to fasten the transducer
directly on the transom, mark the two holes, and drill through them. Screw the
transducer in using the mounting hardware that came in the box, and apply a
generous amount of silicone sealant on both holes both INSIDE and OUTSIDE – this
will make sure that no water will leak through from anywhere – that could be
quite a problem! Even if you are using a plastic block, it’s always a good idea
to use sealant, just in case the hole you drilled touched the transom or made a
hole in it.

Step 4: Run the wires Now that you know how to run the wires, it’s time to do
the actual running! There are two ways you can do this: either above the
transom, or through a hole in the transom. Make sure that if you drill a hole in
the transom, it is WELL ABOVE the water level! It’s good to secure the wire by
clamps or ties every 18 inches or so. This way, they will stay put and not move
around too much.

You also have to run cables from the power source to the main unit. Most
manufacturer’s cables come with a fuse built in. DO NOT remove this fuse!

A power surge can fry your unit! If there isn’t already a fuse, it’s a good idea
to install one! Remember when connecting to the power source that red is
positive and black is negative. Leave the terminals disconnected as you complete
your installation. You can fasten them with whatever kind of connectors you find
more convenient.


FISH FINDERS BASS PRO SHOPS

Step 5: Mount the fish finder By now, you should have a mounted transducer and
wires running from the transducer to your chosen location for your fish finder,
and from your power source to your fish finder location. If your boat has a
dashboard, most fish finders have optional in-dash mounts(sold separately) that
you can use. Trace the area on your dash with a pencil, and cut it out very
carefully.


0 Comments







LEAVE A REPLY.




AUTHOR

Write something about yourself. No need to be fancy, just an overview.


ARCHIVES

December 2018
November 2018
October 2018



CATEGORIES

All


RSS Feed


 * Blog



Powered by Create your own unique website with customizable templates. Get
Started