easysiterogue.weebly.com Open in urlscan Pro
74.115.51.8  Public Scan

Form analysis
0 forms found in the DOM

Text Content

easysiterogue

 * Blog


BAIKAL IZH 27 MANUAL TRANSFER

12/1/2018

0 Comments

 

IZH-46 – EXPLODED VIEW & BAIKAL IZH-46(M) DISASSEMBLY INSTRUCTIONS Thanks to
Todd Cooper for the following information The following instructions were
created as I disassembled my old IZH-46 about 6 years ago. The valve seal was
leaking but I managed to perform the simple repair of a cleaning and relubing
with Pellgun oil. The seal was completely dry. Names and numbers for parts are
taken from the manual that came with the pistol and the below drawing. Back end:
1 – First remove the grip panels by removing the 3 grip screws. 2 – Remove screw
#20.

 1. Baikal Izh 94
 2. Izh 27 Shotgun
 3. Baikal O U Shotguns

This is the small screw in right side of the slide (part #2). 3 – You can then
disconnect the cover tie (65) by sliding the slide forward.


BAIKAL IZH 94

4 – The bar (7) can then be removed by slipping the rear through the notched out
part in the slide (2). Rotate it out. 5 – You can unhook blocking lever spring
(4) from blocking lever using a pair of needle nose plyers.

Baikal® MP-27 (Walnut) OF12B8 OAL LOP PRODUCT CODE 12 GA DESCRIPTION BBL 28” 45
½ ”14 ½ 2 2. Saiga IZ109T1S Upgrade Trade Ad.

6 – Remove large drift pin holding cover lever (57) and blocking lever (3) in
place. Hold these two parts together on removal so you remember how they go. 7 –
The valve stem (17) should slide out with a little coaxing. You might have to
pull the trigger if pistol is cocked. You also have to hold down the valve sear
(14) with a small screwdriver because it blocks removal. The sear is only under
spring tension so little effort is needed to hold it down.

8 – Remove main valve (9) and valve spring (13) from rear of pistol. Sear must
be held down for removal of these parts. That’s as far as I went on the back end
of the pistol.

Front end: 1 – Remove yoke (21). 2 – Remove 2 hinge pins( 8) 3 – Linkages will
slide out now, after the plug (23) and block (26) are removed. Take notice of
how they all go together so you can replace the same way.

4 – Slide linkages and piston out of pistol. 5 – Remove drift pin in frame. I
cannot find part # on this pin.


IZH 27 SHOTGUN

It is the pin that goes through the cylinder (29). It is located below the
“IZH-46” print.

The pin needs a good punch for removal as it is very tight. I made a punch from
an old allen key and hardened it with a propane torch. 6 – Remove cylinder (29)
from frame by rotating counter clockwise. You can put a screwdriver through the
hinge pin hole for leverage. A little heat on the cylinder will help. I danced a
propane flame over the cylinder from a distance until it was very warm to the
touch.

Don’t overdo this. Just warm it up. 7 – There is a rubber packing ring (35) in
the frame that you will see when the compression chamber is removed. Ratatat
discography rar.


BAIKAL O U SHOTGUNS

I removed it and lubed with Pellgunoil to ease reassembly. 8 – Next I made a
small hook from a large paperclip and pulled out the valve seat (30) by hooking
inside it and sliding it out. The valve seat in not fastened in but might be
stuck on the lock (31). The lock is actually the inner seal that I wanted to
look. The hook I made by straightening out the paperclip and bending a very
short(approx 2mm) end at 90 degrees. This hook would enter the valve seat (30)
and provide some pulling ability. 9 – Once the valve seat is out, I hooked the
lock (31) and pulled it out using my paperclip tool.

The lock is a rubber seal that is sandwiched between the valve seat (30) and the
bush (32). I didn’t need to remove the bush so it stayed in place. 10 – The
slide (2) can be removed by sliding it toward the rear sight and pulling it
upwards. The slide spring (12) will pop out to. You can clean under it and
replace.


0 Comments







LEAVE A REPLY.




AUTHOR

Write something about yourself. No need to be fancy, just an overview.


ARCHIVES

November 2018



CATEGORIES

All


RSS Feed


 * Blog




Powered by Create your own unique website with customizable templates. Get
Started